- 492 - .412(10.5) max .185(4.70) .175(4.44) .055(1.40) .045(1.14) .27(6.86) .23(5.84) .11(2.79) .10(2.54) .025(0.64) .014(0.35) .154(3.91) .148(3.74) dia pin1 2 .113(2.87) .103(2.62) .16(4.06) .14(3.56) .037(0.94) .027(0.68) .205(5.20) .195(4.95) .594(15.1) .587(14.9) .56(14.22) .53(13.46) pin 1 pin 2 case positive case gpa1601 thru GPA1607 16.0 amps. glass passivated rectifiers voltage range 50 to 1000 volts current 16.0 amperes features low forward voltage drop high current capability high reliability high surge current capability mechanical data cases: to-220a molded plastic epoxy: ul 94v-0 rate flame retardant terminals: leads solderable per mil-std- 202, method 208 guaranteed polarity: as marked high temperature soldering guaranteed: 260 /10 seconds .16?,(4.06mm) from case. weight: 2.24 grams to-220a dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol gpa 1601 gpa 1602 gpa 1603 gpa 1604 gpa 1605 gpa 1606 gpa 1607 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current .375?(9.5mm) lead length @t c = 100 i (av) 16.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 250 a maximum instantaneous forward voltage @16.0a v f 1.1 v maximum dc reverse current @ t c =25 at rated dc blocking voltage i r 10 ua typical junction capacitance ( note 1 ) cj 100 pf typical thermal resistance (note 2) r jc 2.0 / w operating and storage temperature range t j ,t stg - 65 to + 150 notes: 1. measured at 1 mhz and applied reverse voltage of 4.0 volts d.c. 2. thermal resistance from junction to ambient mounted on heatsink size 2? x 3? x 0.25? al-plate
- 493 - ratings and characteristic curves (gpa1601 thru GPA1607) fig.2- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 2 5 10 20 100 50 50 0 200 150 100 250 300 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.3- typical instantaneous forward characteristics instantaneous for ward current . (a) .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 0.4 0.2 1 4 2 10 20 40 100 200 400 forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o fig.4- typical reverse characteristics instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 .1 .4 .2 1.0 4 40 2 10 100 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 fig.5- typical junction capacitance junction cap acitance.(pf) 1 0 5 10 50 100 1000 500 20 40 60 100 80 120 reverse voltage. (v) tj=25 c 0 fig.1- maximum forward current derating curve average for ward current . (a) 0 50 100 150 8 10 12 14 16 18 case temperature. ( c) o single phase half wave 60hz resistive or inductive load
|
